15% OFF Storewide Sale - Ends Jan 31!

Drip Tape Buying Guide 

Choosing the right drip tape for your project can feel a bit overwhelming.  This guide was designed to simplify the process by walking you through each of the four selections that must be made when choosing a roll of drip tape to purchase. These four selection choices are: the diameter of the tape, the wall thickness of the tape, the emitter spacing and emitter flow rate. After detailing each selection you will find a frequently asked question section at the end of this guide.

Diameter 

There are 4 diameters of drip tape on the market.  The smallest and most common size is ⅝”.  The other sizes are ⅞”, 1 ⅛” & 1 ⅜”.  The majority of drip tape sold is ⅝”.  If you are purchasing drip tape for a garden or small farm where row lengths are 600 feet or less then we highly recommend the ⅝” tape.  The larger sizes are only used in large farming operations.

Wall Thickness

Wall thickness of drip irrigation tape is measured in mil.  Available thicknesses range from 5 - 15 mil. With 5mil being the thinnest and 15 mil being the thickest.   If you are new to using drip tape we strongly recommend starting with 15 mil.  The thinner walled tape is less forgiving and can be damaged easily by someone that is unfamiliar with drip tape installation.  

For home garden use we always recommend 15 mil tape. As it will last several seasons whereas the thinner walled tape will only provide one maybe two seasons of use.  15 mil tape is more expensive, however, being able to use it for multiple seasons will make it less expensive in the long run.  Below is a chart of available wall thicknesses and expected longevity.

Wall ThicknessLife Expectancy 
5 mil1 year
6 mil1 year
8 mil2-3 years
10 mil 2-4 years
12 mil 2-4 years
15 mil 5-10 years


Emitter Spacing

Drip tape has pre-set drip points built into the tape.  So there is no need to buy additional drippers/emitters. It is important to note that no additional emitters can be added to drip tape. Unlike poly tubing, no holes can be punched into dip tape to allow for the insertion of barbed drippers.  Emitters are spaced at one set distance for the entire roll of tape.  For home gardens the most popular spacing is 12”.   That means every 12” there will be a drip point for the entire run of tape.  Emitter spacing is normally matched to the type of crop being watered. Below is a chart with popular emitter spacings and what crops or application use that emitter spacing.

Emitter Spacing (in inches)Crops or ApplicationOther Considerations
4"Flowers, Peppers, GreenhousesGood for Sandy Soil, Short Runs
6"Germination, Onions, GarlicTight Plant Spacings
8"Germination, Strawberries, VegetablesHigh Flow for Sandy Soil
12"Good all around choiceIf Low Flow Emitter Used - Great for Long Runs
60"Blueberries, HopsLong Runs of Plants Spaced Far Apart


Flow Rate Selection

When selecting the flow rate for your drip tape there are 3 considerations to keep in mind.

Run Length –The longer the run length you need per row of tape then the lower the flow rate per emitter is needed. The reason is that longer run lengths have more emitters and the more emitters there are the more water is being used per line.  Thus, in order not to exceed the capacity of a system lower emitter flow rates are used to accommodate for longer runs of tape. For anyone that needs run lengths of 500 feet plus, we recommend using a “low flow” emitter (see chart below).

When planning a home garden tape system run length is not going to be a limiting factor because the rows are generally short and any of the emitter flow rates can be used.

Soil Type –No matter the scale of your drip tape system soil type is a consideration that everyone should think about.  The three main types of soil are Clay, Loam and Sand.  Below is the flow rate selection for each soil type.  

Soil TypeSoil CharacteristicsEmitter Suggestion
ClayDoes not drain wellLow Flow: .11-.16 Gallons Per Hour (GPH)
LoamDrains wellMedium or High Flow: .18 -.46 GPH
SandDrains the fastestHigh Flow: .33-.46 GPH

Filtration – It is important to keep in mind that when choosing emitter flow rate that the lower the flow an emitter has, the smaller the opening for water to drip out is.  This means that lower flow emitters can be more susceptible to clogging.  So it is very important that if using a low flow emitter to have a good filter with at least 200 mesh.  If you know you have water that is hard or has mineral build up it would be best to go with a high flow emitter to prolong the life of the drip tape.

Frequently Asked Questions about Drip Tape

  • Why does drip tape need to operate at a low pressure? – Drip tape is thinner walled than drip irrigation tubing and is designed to work at low pressure.  Too much pressure can cause the tape to burst. It is important that a pressure regulator is installed in your tape system to ensure that the system is operating at or below the specified maximum operating pressure listed. Below is a guide on maximum operating pressure for different sizes of drip tape.
Wall Thickness (mil)5/8" Tape7/8" Tape1 1/8" Tape1 3/8" Tape
58 PSI
610 PSI8 PSI
815 PSI10 PSI8 PSI
1015 PSI15 PSI10 PSI
1215 PSI15 PSI12 PSI
1515 PSI15 PSI15 PSI15 PSI
  • How Do You Install Drip Tape? – Drip Tape is very easy to install.  The video below shows the basics of installing a drip tape system.
  • Can Drip Tape be buried? – Yes, a lot of the drip tape used in large agricultural fields is buried.  Drip Tape can be installed above ground, underground (also called subsurface) or under mulch.
  • Does the emitter need to face up? – Yes, proper installation of drip tape will have the emitter facing up.  Brands like Aqua-Traxx and T-Tape have stripes on their tape and they recommend, “The colored stripe on the drip tape should be facing upward”.
  • Can the tape be flushed with chemical agents to break up build up? –Yes. However, such flushing may prolong the life of the tape but also void any warranty on the tape.  We recommend checking with the tapes manufacturer before performing a flush  and ask about what is best to use and how it affects their warranty.